CorporationsTrade

Discover a World of Business Opportunities at CorporationsTrade

Cart

Your Cart is Empty

Back To Shop
Payment Details
Sub Total $0.00

View cartCheckout

CorporationsTrade

Discover a World of Business Opportunities at CorporationsTrade

Cart

Your Cart is Empty

Back To Shop
Payment Details
Sub Total $0.00

View cartCheckout

CorporationsTrade

Discover a World of Business Opportunities at CorporationsTrade

Cart

Your Cart is Empty

Back To Shop
Payment Details
Sub Total $0.00

View cartCheckout

All Product Categories

Organic waste incineration project

The main waste to be treated in this project is organic waste liquid, which enters the waste liquid storage tank in the incineration unit through various process pipelines for storage.

Compare
Scope of Application
1. Non-combustible high concentration (BOD, COD) wastewater, waste liquid, waste acid, waste alkali, etc;
2. Combustible waste liquid, waste solvent, waste PCB, etc;
Characteristics of waste liquid incinerator
1. Good pulverization effect, it adopts forth generation pulverization device with good burning effect;
2. Without second pollution, low nitrogen burning technology, without any smoke, smell or deleterious gas;
3. High safe performance, ultraviolet supervising system and complete warning system without the danger of explosion;
4. Low malfunction rate, imported parts, dual-loop system, high quality and long lifetime;
5. Good disposal effect with low cost for waste oil, waste liquid, waste solvent and organic waste gas at the same time.
Hazardous waste handling capacity: 10-10000kg/h
Yongxing Kunpeng
The main waste to be treated in this project is organic waste liquid, which enters the waste liquid storage tank in the incineration unit through various process pipelines for storage, and the incineration device processes 2 waste liquids in total. The waste liquid in the waste liquid storage tank is pumped to the waste liquid spray guns on the top of the primary combustion chamber and the bottom of the secondary combustion chamber. Under the action of compressed air, the waste liquid enters the incinerator after being atomized. Under the action of oxygen-supplementing wind, the waste liquid is fully burned in the incinerator. The ash enters the slag discharger and is finally transported to the silo for storage. The flue gas enters the secondary combustion chamber again, and combustible gases such as long and short chain hydrocarbons and CO in the flue gas are further turbulently mixed under the torsion of the secondary air, and can be fully exhausted under the "3T+E" environment. Combustion will completely decompose dioxin-like substances. Under normal circumstances, the furnace temperature in the combustion chamber is above 1100°C, and the designed total residence time is above 2 seconds. The organic hazards in the flue gas are completely destroyed and transformed into CO2, SOX, and HCl gases to achieve the purpose of complete sterilization, disinfection, and deodorization.
The high-temperature flue gas that is fully burned in the secondary combustion chamber directly enters the waste heat steam boiler (membrane wall boiler) to cool down to about 500°C. The inlet of the steam boiler is equipped with a SNCR denitrification system (in-furnace denitrification) interface to remove nitrogen and oxygen. compound. The flue gas then enters the quenching deacidification tower, where it is sprayed with dilute lye, and the temperature is lowered to about 200°C within 1 second to prevent the re-production of dioxins. Then, hydrated lime and activated carbon are sprayed into the dry spray tower to remove HCl, SO2, HF and other acid gases in flue gas and remove heavy metals and dioxins in flue gas. Then the flue gas enters the bag filter to remove particulate matter such as fly ash and waste activated carbon. The purified flue gas enters the flue gas reheater through the induced draft fan for heat exchange, and then enters the packing spray tower to further purify the acidic components and dust, and wash the cooled flue gas. The gas then enters the front-end flue gas reheater coil for heat exchange and whitening. Finally, the flue gas that reaches the standard is discharged at high altitude through the chimney.
Flow chat

Organic waste incineration project

Category:

Reviews

There are no reviews yet.

Be the first to review “Organic waste incineration project”

Your email address will not be published. Required fields are marked *

Related products

  • Contact Us

    Gel sealed Mini-pleat HEPA filter（top gel seals）

    The two-component gel is poured into the liquid seal type HEPA filter , and this is used as an installation seal.

  • Contact Us

    KSZ-3.0D1/D2 welding exhaust hose

    KSZ-3.0D1/D2 welding exhaust hose Features:
    ● High efficiency custom aluminum impeller
    ● Self-supporting & self-positioning suction hood
    ● Durable flexible suction arm, high temperature resistance & flame retardant & abrasion resistance
    ● Easy to replace and clean filters, no frequent maintenance is required
    ● Imported filter material with high precision filtration
    ● Special designed dust cleaning device, automatic blow-back cleaning
    ● Siemens PLC smart control system, more intelligent and energy saving
    ● Integrated automatic fire extinguish system

  • Contact Us

    Oil Injector for Drying Room Chain

    The oil injection system adopts PLC automatic control.

  • Contact Us

    KSDM-4.0 Downdraft Grinding Dust Collector

    Features:
    ● Low noise
    ● Stable performance
    ● Easy operation and use High purification efficiency
    ● Meeting indoor emission standards Reasonable structure design
    ● Low resistance loss

  • Contact Us

    LCTW Dynamic pass box

    The self-cleaning transfer window allows for the transfer of materials, utensils, and other items under Class A environmental protection. Items are self-cleaned within the window before entering areas of higher cleanliness. The self-cleaning transfer window is equipped with an ultraviolet sterilization lamp and can also be fitted with a royal oxygen sterilization system according to user requirements.